Zebra S4M Uživatelský manuál Strana 70
- Strana / 132
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Configuration
Control Panel LCD Display
64
13290L-001 Rev. A S4M User Guide 10/21/05
CONTROL CODES
(APL-D mode only)
Set APL-D Control Codes
Selections: STANDARD, MAINFRAME
Default Value: STANDARD
To modify this parameter:
• Press the up or down arrow to scroll through the selections.
MODULE A
(APL-D mode only)
Set Module A Storage Device for APL-D
Selections: NONE, RAM 1, RAM 2, FLASH 1, FLASH 2
Default Value: NONE
To modify this parameter:
• Press the up or down arrow to scroll through the selections.
MODULE B
(APL-D mode only)
Set Module B Storage Device for APL-D
Selections: NONE, RAM 1, RAM 2, FLASH 1, FLASH 2
Default Value: NONE
To modify this parameter:
• Press the up or down arrow to scroll through the selections.
RESOLUTION
(APL-I mode only)
Set Printer Resolution for APL-I
Sets the dot size for backward compatibility with some older APL-I
printers.
Selections: 5 MIL, 10 MIL, 15 MIL
Default Value: 5 MIL
To modify this parameter:
• Press the up or down arrow to scroll through the selections.
LENGTH
Set Maximum Label Length
Maximum label length is used in conjunction with the calibration
procedure. The value of this setting is the maximum label length that is
used during the media portion of the calibration process. Only a few labels
are required to set media sensors. Always set the value that is at least 1 in.
(25.4 mm) longer than the longest label to be used on the printer.
Selections:
AUTO, < 1 INCH (25.4 mm) to < 39 INCH (991 mm)
Default Value:
AUTO
To modify this parameter:
• To increase the value, press the up arrow.
• To decrease the value, press the down arrow.
Table 10 • Printer Parameters, Password Levels 1 and 2 (Page 5 of 5)
Parameter Explanation
- User Guide 1
- Contents 3
- Who Should Use This Document 8
- Contacts 9
- Document Conventions 10
- FEED button 11
- CANCEL button 11
- About This Document 12
- Introduction 13
- External View 14
- Control Panel 15
- FEED FEED 16
- Appearance 17
- Control Panel Lights 18
- Printer Media Compartment 19
- Printer Language Modes 20
- Printer Setup 21
- Before You Begin 22
- Inspect the Printer 23
- Report Shipping Damage 23
- Store the Printer 23
- Shipping 23
- Select a Site for the Printer 24
- Power Cord Specifications 26
- Connector Locations 27
- Types of Connections 28
- Operations 29
- 16.4 ft (5 m) maximum 30
- Types of Media 31
- Outside Inside 33
- Adhesive Test 34
- Ribbon Scratch Test 34
- Labels Tag Stock 36
- Roll Media 37
- Fanfold Media 38
- Load Media in Tear-Off Mode 39
- 4. Slide out the media guide 40
- Close the printhead assembly 41
- Load Media in Peel-Off Mode 42
- Slide out the media guide 43
- Tear-off/peel-off bar 45
- Peel assembly 45
- Peeling starts automatically 46
- Load Ribbon 47
- Caution • 50
- 1). At the same 51
- Calibrate the Printer 52
- Position the Media Sensors 53
- Left Dial Right Dial 55
- If the media... Then 56
- Configuration 57
- ENTER button 58
- MENU or any arrow button 59
- Password 60
- Printing Configuration Labels 62
- SETTINGS 63
- LIST NETWORK 64
- Select a Display Language 65
- Parameter Explanation 66
- To modify this parameter: 66
- TEAR OFF 67
- LABEL TOP 67
- X FORMS ADJUST 67
- Y FORMS ADJUST 67
- Media Type Sensor Used 68
- PRINT SPEED 69
- PRINT WIDTH 69
- COMPAT. MODE 69
- Control Panel LCD Display 70
- To print labels: 71
- PRINT PAGE 72
- PRINT FORMAT 72
- DATA BITS 72
- COMMAND CHAR 74
- DELIM. CHAR 74
- CONTROL CHAR 74
- CHANGE RTC DATE 75
- CHANGE RTC TIME 75
- 1. Press ENTER 76
- 1. Press ENTER to select YES 76
- ZPL OVERRIDE 77
- EPL OVERRIDE 77
- SENSOR PROFILE 77
- ZebraNet 80
- Routine Maintenance 83
- Lubrication 84
- Cleaning Procedures 84
- Clean the Peel-Off Assembly 88
- Troubleshooting Checklists 92
- LCD Error Messages 93
- HEAD COLD 94
- HEAD ELE. BAD 94
- Memory Errors 95
- Print Quality Problems 96
- Calibration Problems 99
- Communications Problems 100
- O) and then 101
- Troubleshooting 102
- O) and then On (l) 103
- CANCEL Self Test 104
- PAUSE Self Test 105
- FEED Self Test 106
- Printer Diagnostics 107
- Print Quality Description 108
- O) and then back 109
- Specifications 111
- General Specifications 112
- Agency Approvals 113
- Printing Specifications 114
- Media Specifications 115
- Ribbon Specifications 116
- ZPL II Commands 117
- Parameters Details 118
- Proprietary Statement 119
- Liability Disclaimer 120
- Limitation of Liability 120
- Glossary 121
- HEAD COLD message, 88 126
- HEAD TOO HOT message, 87 126
- RIBBON IN message, 87 128
- Part Number: 13290L-001 132
- © 2005 ZIH Corp 132
Související produkty a manuály pro ne Zebra S4M
ne Zebra MIX05120 Uživatelský manuál
(2 stránky)
(2 stránky)
ne Zebra GK888t Uživatelský manuál
(20 stránky)
(20 stránky)
ne Zebra GK420d Uživatelský manuál
(20 stránky)
(20 stránky)
ne Zebra P100i Uživatelský manuál
(76 stránky)
(76 stránky)
ne Zebra RW 220 Uživatelský manuál
(16 stránky)
(16 stránky)
Alto-Shaam 1200-TH/III manuály
Uživatelské manuály a uživatelské příručky pro Pec Alto-Shaam 1200-TH/III.
Poskytujeme 1 manuály pdf Alto-Shaam 1200-TH/III ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentáře k této Příručce