Zebra TTPM2 Uživatelský manuál stáhnout pdf

TTPM2 Firmware No. 906/907-xxx

906-213 means program version 2.13, etc.

FW version

Change

906-213

Start of FW history.

907-214

This FW version has only been used in dual ticket track applications.

•

Handling of dual tracks modified.

•

Ticket will be erased magnetically before being striped or voided.

•

XON will be sent once every 30 second if XON / XOFF is selected.

906/907-216

•

Start up routine modified. Cutter no longer operates at start up since this

may damage a ticket inserted from the front in case of a power failure in

the middle of an operation.

•

Cutter can be initialized by the "3-button reset operation"

•

Time-outs are now implemented for the !L3 function.

•

Minor modifications to the front load sequence.

906/907-217

!L3 now answers with ACK if card is loaded correctly and with NAK + error code in

case of a load failure.

The following error codes have been defined:

•

- NAK + B No card inserted within 10 seconds after received !L3.

- NAK + C Card inserted and then removed.

- NAK + D Card jam when loading card (serious fault)

•

An error in FW version 2.16 caused problems if a ticket was read with !D

and then printed without sending a new !M command before the !P. The

ticket was then striped. This is now corrected.

906/907-218

•

Command !N has been introduced to allow encoding of up to

approximately 50 characters on track 2 in hexadecimal format.

Characters 0—9 and A—F are valid. The least significant bit is encoded

first. No additional characters are added by the TTPM. It is, therefore,

necessary to put approximately six ZERO digits at the beginning of the

data to be encoded. Any start bits, stop bits, or check digit also have to

be included in the data string.

•

Reading a ticket encoded with !N, by the use of the !D command, will not

work since !D expects a ticket to have a correct ISO format.

•

Read after write on track 2 has been slightly improved.

•

Cutter is now reset at power up if no ticket is present in any of the

sensors close to the cutter. This prevents a ticket from being accidentally

cut, but enables the cutter to be reset in the event of a failure, or after

maintenance.

906/907-219

•

Command !O added. Reads track 2 of the magnetic stripe and reports the

result by returning up to 240 characters (0 or 1) representing the bits

encoded on the t

rack No decoding is made by the TTPM2 This command

1 2 3 4 5 6

Shrnutí obsahu

Strany 1

TTPM2 Firmware No. 906/907-xxx 906-213 means program version 2.13, etc. FW version Change 906-213 Start of FW history. 907-214 This FW version has

Strany 2

is useful if a card has been encoded with an equipment that does not follow the ISO standards, or by a TTPM2 by the use of command !N. • A separate v

Strany 3

• Paper is automatically positioned at power on. 906/907-232 • The time-out for the !L3 command is increased. • The printer will automatically try t

Strany 4

and 57600 bps in addition to the default speed 9600 bps. • To enhance ticket handling speed, front load printers read track 2 data to memory when loa

Strany 5

( |, {, and } ) Only dual track version: Does not accept ticket data without track selection command. !L1, !L2, !L17, or !L18 must always be sent pri

Strany 6

used as single entry one's. It is now possible to suspend operation after magnetic encoding by inserting a ~ character in the !M data string. A b

Další dokumenty pro Tisk a skenování Zebra TTPM2

Zobrazit dokument Zebra TTPM2 Specifikace

Zebra TTPM2 Specifikace (140 stránky)

Zobrazit dokument Zebra TTPM2 Servisní příručka

Zebra TTPM2 Servisní příručka (22 stránky)

Zobrazit dokument Zebra TTPM2 Uživatelský manuál

Zebra TTPM2 Uživatelský manuál (34 stránky)

Komentáře k této Příručce

Žádné komentáře