Zebra RZ Series Uživatelská příručka stáhnout pdf (Strana 57)

Operations

Load Media

1/11/11 Z Series

/RZ™ Series User Guide 79695L-003

10. Slide in the media guide until it touches the outer edge of the media.

11. Set the printer to Rewind mode. See Select Print Mode on page 76 for instructions.

12. Close the printhead assembly.

13. If the printer is paused (the Pause light is on), press PAUSE to enable printing. Rewinding

begins automatically.

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 153 154

Z Series 1
/RZ™ Series 1
User Guide 1
Part Number: 79695L-003 2
Declaration of Conformity 3
Compliance Information 4
Contents 5
Section Description 10
T: Telephone 11
F: Facsimile 11
E: E-mail 11
Document Conventions 12
FEED button 13
CANCEL button 13
About This Document 14
Introduction 15
External View 16
Printer Media Compartment 18
Control Panel 19
Control Panel Buttons 20
Control Panel Lights 21
Printer Language Modes 22
Printer Setup 23
Before You Begin 24
Temperature Relative Humidity 25
Select a Site for the Printer 26
I) may damage the 27
Interface 29
Standard or 29
Optional 29
Description 29
O) position 32
Power Cord Specifications 33
Types of Media 34
Ribbon Overview 36
If the ribbon... Then 37
Operations 39
Print Mode Printer Option 41
Load Media 43
Roll Media 44
Fanfold Media 44
Roll Media (Continued) 45
Fanfold Media (Continued) 45
PAUSE to enable printing 47
Close the printhead assembly 57
Ribbon Coated Outside 58
(black ribbon spindle) 58
Ribbon Coated Inside 58
(gray ribbon spindle) 58
Load Ribbon 59
Remove Used Ribbon 62
Calibrate the Printer 63
Media Width 64
If the media... Then 65
Adjust Printhead Pressure 66
Configuration 67
Setup Mode 68
Exit Setup Mode 69
Default Password Value 70
SETUP/EXIT 71
LIST SETUP 71
PLUS (+) to confirm printing 71
LIST NETWORK 72
Language/Parameter 73
To change the value shown: 73
Action/Explanation 74
WARNING REPLACE 80
To format a memory card: 83
To initialize Flash memory: 84
To print a sensor profile: 84
LOAD BACKING prompt displays 85
RELOAD ALL displays 86
To skip these parameters: 94
IDLE DISPLAY 96
Replacing Printer Components 100
Lubrication 100
Area Method Interval 101
Routine Maintenance 102
Cleaning Procedures 102
Clean the Cutter Module 106
I) the printer 107
Troubleshooting 111
Troubleshooting Checklists 112
LCD Error Messages 113
O) the printer 114
HEAD COLD 115
HEAD TOO HOT 115
DEFRAGMENTING 116
ERROR CONDITION 116
CUTTER JAM 116
OUT OF MEMORY 116
(function) 116
Print Quality Problems 117
Note • A vertical drift of 119
Calibration Problems 120
NONE. See 121
Ribbon Problems 122
RFID Problems 123
MEDIA POWER UP and 125
LANGUAGE 126
SAVE CHANGES in the 126
O) and then on (I) 127
CANCEL self tests 129
CANCEL Self Test 130
PAUSE Self Test 131
FEED Self Test 132
Print Quality Description 133
FEED and PAUSE Self Test 135
Printer Diagnostics 136
RIBBON (2). If 137
MEDIA (3) for the media 137
Specifications 139
General Specifications 140
Printing Specifications 141
Media Specifications 143
Ribbon Specifications 144
Printer Options 145
1/11/11 Z Series 147
79695L-003 Z Series 148

Komentáře k této Příručce

Žádné komentáře

Zebra RZ Series Uživatelská příručka Strana 57

Komentáře k této Příručce

Související produkty a manuály pro Tisk a skenování Zebra RZ Series