Zebra 170PAX2 Series Uživatelská příručka Strana 13

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 100
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 12
11
10. Rotate the peel roller assembly (J) up until it latches closed.
11. Thread the backing material under the lower guide post (M) and around the take-up
spindle of the applicator (refer to the applicators users manual).
Ribbon Loading
To load ribbon, refer to Figure 4 on page 12 (for right-hand units) or Figure 5 on
page 13 (for left-hand units).
NOTE: Do not load ribbon if the print engine is to be used in the direct thermal
mode.
CAUTION: When installing the ribbon roll on the ribbon supply spindle, make
sure to push the ribbon roll against the stop with the ribbon aligned squarely with
its core. Do not use ribbon narrower than the media. If the printhead is not pro-
tected by the smooth backing of the ribbon, premature printhead failure may
result due to excessive abrasion.
Right Hand Units
1. Push the ribbon roll onto the supply spindle (N) as far as it will go, so the ribbon
feeds as shown in Figure 4 on page 12.
2. Install an empty ribbon core onto the ribbon take-up spindle (O).
3. Open the printhead assembly (C) by unlatching the print- head lock lever (D) from
the locking pin (E).
4. Thread the ribbon below the lower ribbon guide roller (P), under the printhead
assembly (C), and up and over the upper ribbon guide roller (Q) as shown in Figure
4. Use caution not to crease or wrinkle the ribbon!
5. Attach the ribbon to the take-up spindle core (use a label if needed) and wind for
several turns in the direction shown in Figure 4.
6. Close the printhead assembly (C) by latching the printhead lock lever (D) onto the
locking pin (E).
7. Insure the ribbon is located between the Ribbon Sensor and the Sensor Reflector
positioned above it.
Zobrazit stránku 12
1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 99 100

Komentáře k této Příručce

Žádné komentáře

Alto-Shaam 1200-TH/III manuály

Uživatelské manuály a uživatelské příručky pro Pec Alto-Shaam 1200-TH/III.
Poskytujeme 1 manuály pdf Alto-Shaam 1200-TH/III ke stažení zdarma podle typů dokumentů: Uživatelský manuál






Další produkty a příručky pro Pec Alto-Shaam

Modely Typ Dokumentu
12-20 RTM Uživatelský manuál   Alto-Shaam 12-20 RTM User Manual, 2 stránky
767-SK Uživatelský manuál   Alto-Shaam 767-SK User Manual, 2 stránky
COMBITHERM 20.20ESG Uživatelský manuál   Alto-Shaam COMBITHERM 20.20ESG User Manual, 107 stránky
1000-TH/III Uživatelský manuál   Alto-Shaam 1000-TH/III User Manual, 42 stránky
7.14ESG Over Uživatelský manuál   Alto-Shaam 7.14ESG Over User Manual, 4 stránky
1000-TH-II/Spilt Uživatelský manuál   Alto-Shaam 1000-TH-II/Spilt User Manual, 2 stránky
ECO SMART 1200-TH/III Uživatelský manuál   Alto-Shaam ECO SMART 1200-TH/III User Manual, 41 stránky
Halo Heat 1000-TH-I Uživatelský manuál   Alto-Shaam Halo Heat 1000-TH-I User Manual, 22 stránky
MN-29492 Uživatelský manuál   Alto-Shaam MN-29492 User Manual, 53 stránky
Combitherm 10 10ES Uživatelský manuál   Alto-Shaam Combitherm 10 10ES User Manual, 6 stránky
ED2-48 Uživatelský manuál   Alto-Shaam ED2-48 User Manual, 44 stránky
2-ASC-2E/STK Uživatelský manuál   Alto-Shaam 2-ASC-2E/STK User Manual, 2 stránky
Combitouch Series 7.14es CombiTouch Uživatelský manuál   Alto-Shaam Combitouch Series 7.14es CombiTouch User Manual, 51 stránky
Combitherm 1008 Uživatelský manuál   Alto-Shaam Combitherm 1008 User Manual, 135 stránky
ecosmart Electronically Operated Ovens Uživatelský manuál   Alto-Shaam ecosmart Electronically Operated Ovens User Manual, 91 stránky
HN2SYS-96 Uživatelský manuál   Alto-Shaam HN2SYS-96 User Manual, 2 stránky
COMBITOUCH MN-29245 Uživatelský manuál   Alto-Shaam COMBITOUCH MN-29245 User Manual, 38 stránky
750-CTUS Uživatelský manuál   Alto-Shaam 750-CTUS User Manual, 19 stránky
1000-SK/II Uživatelský manuál   Alto-Shaam 1000-SK/II User Manual, 30 stránky
Cook & Hold Oven Electronic Control 1000-TH/II Uživatelský manuál   Alto-Shaam Cook & Hold Oven Electronic Control 1000-TH/III User Manual, 49 stránky