Zebra XiII-Series Uživatelský manuál Strana 43
- Strana / 118
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Leaving the Program Mode
You can leave the Program Mode at any time by pressing the Setup/Exit
key. The SAVE CHANGES display will appear. There are five choices,
described below. Pressing the left or right black oval key displays other
choices and pressing the Next/Save key selects the displayed choice.
PERMANENT - permanently saves the changes. Values are stored in
the printer even when power is turned off.
TEMPORARY - saves the changes until changed again or until power
is turned off.
CANCEL - cancels all changes since pressing the Setup/Exit key except
the Darkness and Tear-Off settings (if they were changed).
LOAD DEFAULTS - loads factory defaults. The factory defaults are
shown on the following pages.
NOTE: Loading factory defaults will require ptinter calibration and
resetting the Head Resistor value.
LOAD LAST SAVE - loads values from the last Permanent Save.
Zebra XiII-Series User’s Guide 31
43
H:...Xi2UsersGuideR2.vp
Fri Aug 07 10:35:48 1998
Color profile: Disabled
Composite Default screen
- Zebra XiII-Series 1
- Fri Aug 07 08:59:37 1998 2
- Warranty Information 3
- Contents 5
- Operation 21 6
- Fri Aug 07 10:33:15 1998 7
- Options 71 8
- Specifications 77 8
- Appendix 87 9
- Glossary 99 9
- Index 103 9
- H:...Xi2UsersGuideR2.vp 10
- Fri Aug 07 10:33:16 1998 10
- Color profile: Disabled 10
- Composite Default screen 10
- List of Figures 11
- List of Tables 12
- Getting Started 13
- System Requirements 14
- Media and Ribbon Requirements 15
- Unpacking 15
- Fri Aug 07 10:34:39 1998 16
- Site Requirements 17
- Communications 18
- Loading Media 18
- Non-Continuous Media 19
- Continuous Media 19
- Black-Mark Media 19
- Tear-Off Mode Media Loading 20
- REWINDPEEL-OFF 21
- TEAR-OFF 21
- CUTTER REWIND 21
- BOTTOM SUPPLY REAR SUPPLY 22
- Continuous Media Loading 23
- Cutter Mode Media Loading 23
- Rewind Mode Media Loading 23
- Fri Aug 07 10:34:43 1998 24
- Peel-Off Mode Media Loading 26
- Transmissive Media Sensor 27
- Position Adjustment 27
- MEDIA SENSOR 28
- ADJUSTMENT 28
- Lower Media Sensor Adjustment 29
- STRIP OF MEDIA 30
- 6-12 INCHES LONG 30
- Fri Aug 07 10:34:46 1998 31
- Ribbon Removal 32
- Operation 33
- Peel-Off Mode 34
- Rewind Mode 34
- Cutter Mode 34
- Operator Controls 35
- Front Panel Display 36
- Front Panel Keys 37
- Front Panel Lights 38
- Printer Status Sensors 39
- Initial Printer Power-Up 40
- Configuration and Calibration 41
- Fri Aug 07 10:35:48 1998 42
- Leaving the Program Mode 43
- Fri Aug 07 10:35:49 1998 45
- Fri Aug 07 10:35:50 1998 50
- Fri Aug 07 10:35:51 1998 54
- Fri Aug 07 10:35:52 1998 57
- Sample ZPL II Label Formats 58
- Fri Aug 07 10:35:53 1998 62
- Routine Care and Adjustment 63
- Cleaning the Exterior 64
- Cleaning the Interior 64
- Cleaning the Sensors 65
- Lubrication 66
- Fuse Replacement 66
- Fri Aug 07 10:36:17 1998 67
- ADJUSTING 68
- AVAILABLE 68
- Printhead Pressure Adjustment 69
- Fri Aug 07 10:36:20 1998 70
- Fri Aug 07 10:36:37 1998 71
- Fri Aug 07 10:36:38 1998 72
- Printer Diagnostics 77
- Cancel Key Self Test 78
- Pause Key Self Test 79
- Feed Key Self Test 80
- Fri Aug 07 10:36:39 1998 81
- Fri Aug 07 10:36:40 1998 82
- Rewind Option 83
- Memory SIMMs 84
- On-Line Verifier 84
- Applicator Interface 85
- Media Supply Spindle 85
- Optional Media Supply Fins 85
- PCMCIA Type I Memory Cards 86
- KMT Printhead 86
- Communication Interfaces 86
- RS-485 Interface 87
- Fri Aug 07 10:36:58 1998 88
- Specifications 89
- Bar Codes 90
- General Specifications 91
- Printing Specifications 92
- Ribbon Specification 92
- Media Specifications 93
- Fri Aug 07 10:37:27 1998 94
- Standard 95
- Optional Printer Fonts 97
- @ABCDEFG 98
- Appendix 99
- Fri Aug 07 10:37:51 1998 100
- RS-232 Interconnections 101
- Fri Aug 07 10:37:52 1998 102
- Rear Panel DB-25S 103
- RS-422/RS-485 Connector 103
- Parallel Data Port 104
- Cabling Requirements 105
- ASCII Code Chart 106
- Fri Aug 07 10:37:54 1998 107
- Too Dark 108
- Slightly Dark 108
- Slightly Light 108
- Too Light 108
- “In-Spec” 108
- Figure 29. Bar Code Examples 109
- Fri Aug 07 10:37:57 1998 110
- Glossary 111
- Fri Aug 07 10:38:13 1998 112
- Fri Aug 07 10:38:14 1998 113
- Fri Aug 07 10:38:32 1998 115
Související produkty a manuály pro Tiskárny štítků Zebra XiII-Series
Tiskárny štítků Zebra XiIII Series Uživatelský manuál
(116 stránky)
(116 stránky)
Tiskárny štítků Zebra Z4M Uživatelský manuál
(57 stránky)
(57 stránky)
Tiskárny štítků Zebra 105SL Uživatelský manuál
(130 stránky)
(130 stránky)
Tiskárny štítků Zebra Printers Uživatelský manuál
(69 stránky)
(69 stránky)
Tiskárny štítků Zebra LI 72 Uživatelský manuál
(62 stránky)
(62 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce